Ru


En

Город

Дилер

Екатеринбург (343) 217 02 02

Москва (495) 660 52 00

WATERPLUG

Ватерплаг

DOWLOADD (pdf)

WATERPLAG

DESCRIPTION

WATERPLUG® is a rapid setting, cementitious waterstop designed to stop active water leaks and moisture ingress. 

RECOMMENDED FOR

WATERPLUG® can be used internally or externally as a temporary waterproof plugging mortar or where rapid setting and early strength gain is required.

  • Plugging/stopping active water leaks
  • Sealing of leaking joints, form tie holes or cracks WATERPLUG® can be used on the following substrates:
  • Concrete
  • Masonry
  • Earthenware
  • Stone 

ADVANTAGES

  • Stops water flow
  • Sets in approximately 2 minutes after mixing
  • Durable
  • Can be used underwater
  • Can be mixed with water or used dry
  • Easy to apply
  • Packaged in easy to use, re-sealable containers
  • Zero VOC - PENETRON powdered products contain zero volatile organic compounds and are safe for use both outdoors and in confined indoor spaces.

DIRECTIONS FOR USE

Surface Preparation: The substrate must be clean, sound and free of any surface contamination, such as oils, coatings, paints, dirt, etc. Leaking areas must be cut back to sound material, leaving an appropriate chase for receiving WATERPLUG®. 

Mixing

Setting time is dependent largely on the amount of mixing water used. Standard mixing ratio at 20°C is 1.1 kg WATERPLUG® and approximately 0.25 l of water. Water must be added to WATERPLUG® and mixed quickly. The mix should have a dry pack (dry earth) consistency, holding a shape when squeezed in your hand but easily crumbled when pressed with fingers. Mixing time is about 15 seconds with setting occurring about 30 seconds later. In cold weather, use lukewarm water. In higher temperatures, use cold water. 

Application

To avoid waste, only small quantities of WATERPLUG® should be mixed. After mixing, apply WATERPLUG® to the appropriate area immediately. Material should be formed into a wedge and forced into the leak. This can be accomplished with the use of a block of wood and hammer. Work the plug well into the area and then, applying as much pressure as possible, hold firmly in place for about 2 minutes or until set. After the leak has stopped, prime the area with a bond coat of PENETRON® and then fill the remaining void to the surface with PENECRETE MORTAR™. Remove excess material. After lightly pre-wetting, apply a final coat of PENETRON® to the repaired area.

PACKAGING

This product can be purchased in 25 kg and 5 kg pails.

STORAGE / SHELF LIFE

WATERLUG® should be stored dry at any temperature and humidity. When properly stored in a dry cool place in unopened and undamaged original packaging, shelf life is 18 months. 

SAFE HANDLING INFORMATION

WATERPLUG® contains cement which is alkaline. Will irritate eyes and skin and may cause skin sensitization. Wear appropriate eye, skin and breathing protection when using this product. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. For further information please refer to Material Safety Data Sheet.

KEEP OUT OF REACH OF CHILDREN.


8 800 200 70 92

Главный офис в Екатеринбурге: пл. Жуковского, 1 [карта] +7 (343) 217-02-02

Политика обработки персональных данных

Представительство в Москве: Рязанский проспект, 24, стр.2 [карта] +7 (495) 660-52-00

© 1991-2010
ГК «Пенетрон-Россия»

ГК «Пенетрон-Россия»
Россия, Свердловская область, 620076, Екатеринбург, пл. Жуковского, 1
info@penetron.ru
+7 (343) 217-02-02
ГК «Пенетрон-Россия»
Россия, Московская область, 109428, Москва, Рязанский проспект, 24, стр.2
info@penetron.ru
+7 (495) 660-52-00